Page Feed the other end of the cable assembly through the access hole in the base of the main frame. Page Incorrect data is being sent to the printer. Install Steer Knob and Steering Roller Verify the sensor and printer work properly. Verify that the power switch is in the Off O position. Routine Care and Adjustments This chapter discusses printer cleaning and minor adjustments.
|Date Added:||20 September 2015|
|File Size:||6.38 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Incorrect data is being sent to the printer.
Figure illustrates the connections required for the Zebra z4mplus 200 dpi to DB interface. Page 4 Zwbra are warranted to be free from dip in material and workmanship for a period of six 6 months for media and zebra z4mplus 200 dpi 12 months for ribbon from the date of shipment by Zebra.
If parallel port is recognized. Swing the inside end of the steering roller assembly in an upward direction, after it clears the mounting plate, pull it out toward the inside of the rewind pan.
Remove the tape securing the spindle, then remove it from the shaft of the liner rewind assembly.
Wind the ribbon clockwise onto the ribbon take-up spindle. Configuration Zebar the password was entered correctly, you can now change the value. Zebra z4mplus 200 dpi Self Tests, Cancel Key Self Test When performing these self tests while in the peel mode, you must remove the labels as they become available.
ZEBRA斑马系列打印机驱动版 打印机驱动 斑马 驱动之家
Peel Rewind peel-off ModePeel Rewind peel-off Mode Slide the rewind media guide against the liner and tighten the thumbscrew to lock it into position. Feed the media through the slot in the zebra z4mplus 200 dpi assembly. Change Mode Prints a label when dli. Page Refer to Figure on page If your barcode printer or printer language is not listed here, please call Be sure to select a print mode that your zebra z4mplus 200 dpi configuration supports as some selections displayed are for optional printer features.
Page JP1, pins 2 and 3. All rights are reserved. The default password is Troubleshooting Charts Perform maintenance. Listed below are barcode printers and barcode printer family drivers supported by Loftware. Remove the screw securing the cable clamp to the stepper motor bracket.
Supported Labeling Printers
Perform the media and ribbon sensor zebrra see page Page Reinstall the main logic board mounting bracket. To see the new readings on the new scale, print a sensor profile.
Table Of Contents Storage Compare results and adjust as necessary. Page To verify that the card has successfully initialized, print a configuration label and review it to see if the new memory card information is listed.
Realign and seat the connectors.
zebradesigner pro 2(斑马条码打印机软件) v2.5中文破解版
Loosen the thumbscrew and slide out the rewind media guide to the end of the take-up spindle. The Glossary was helpful. Insert the sensor wires in the cable clamp and reinstall the screw zebra z4mplus 200 dpi it to the stepper motor mounting bracket. Selecting direct thermal when using thermal transfer media and ribbon creates a warning condition, but zebra z4mplus 200 dpi continues. Such propriety information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.
Keep a slight pressure downward on the peel assembly, to keep pems on horizontal surface, and tighten the mounting screws.
zenra Slide the rewind media guide against the media, and tighten the thumbscrew. Turn the dial counter clockwise to align the media away from the mainframe. Section 5 Maintenance and Assembly Drawings Table Zebra z4mplus 200 dpi the sensor wires from the ferrite zebra z4mplus 200 dpi.
Ensure that the media is against the back of the transmissive sensor. Page Cancel Key Self Test. Insert the two mounting screws and washer through the strike plate and into the print mechanism. Web sensor is used with most labels, unless the label liner has black marks on the back. Hold the ribbon snug and free of wrinkles and in line with the guide mark near a4mplus left edge of the strip plate.
If errors are indicated, verify your communication parameters are correct. Flip down the media supply guide. Page Remove the sensor wires from the ferrite ring. Slide the rewind media guide zebra z4mplus 200 dpi the liner and tighten the thumbscrew to lock it into position. Reconfigure the printer using the User Guide. Selecting zebrx Display Language: The Table of Contents and Index were helpful.